homebridge-domintell

This plugin creates a connection to a Domintell Master and uses the Legacy LightProtocol to get or set information to the Master. The code has been tested against DGQG04 Master.

Supported modules

This code has been tested against several modules, including:

• DGQG04: Master
• DBIR01: 8 bipolar relays
• DDIM01: 8 dimmer commands
• DINTDALI01: DALI interface
• DISM20: 20 input module (04 and 08 variant should also work; but not tested)
• DPBRLCD02: Rainbow LCD push buttons (only temperature readout)
• DTRV01: 4 shutter inverters
• DMOV05: Infrared detector (DMOV01 and DMOV02 should also work; but not tested)
• DOUT10V02: 0-10V output module

General configuration

Setting up the connection to the Domintell Master is quite easy. There are four parameters that are used:

• ip: You will need to define the IP address of the Domintell master. This parameter is required.
• port: if another port than the default 17481 is required, specifiy it here
• username: provide the username if authentication is required. Leave blanc to disable authentication.
• password: provide the password for the user defined above.

Please note that password protected logins are not yet tested.

Adding accessories

Accessories can also be added through the configuration file. The reason for choosing a configuration file is because it is more flexible than automatically reading the APPINFO from Domintell. Now you can define what kind of accessorie is connected to a digital output.

All accessories should be added to the 'accessories' list. Each accessory consists of:

• Identifier: This is the unique identifier for your accessory. You can obtain this information with the APPINFO output. The length is typical 9 to 12 bytes. Some examples are (note that the spaces between module name and serial number need to match whatever APPINFO returns):

  • DAL 89-03 : Addresses the third DALI interface with serial 89
  • DIM 2185-1 : The first dimmer output of the module with serial 2185
  • PRL 130 : Rainbow LCD Push Button with serial 130 (currently only the reading of the temperature is supported)
  • I20 23A-4 : The fourth input of the input module with serial 23A

• Name: the name you wish to give to your accessorie. This does not need to match with the Domintell name

• Type: you can choose what type of object this accessory is.

  • Lightbulb: a typical light bulb, which can be turned on or off (0 or 1)
  • DimmableLightbulb: a dimmable lightbulb which receives a value between 0 and 100
  • Outlet: an outlet which can be turned on or off (0 or 1)
  • WindowCovering: used for screens which go up and down
  • TemperatureSensor: currently reads the temperature information from the 6-button LCD screen
  • ContactSensor: when an input is connected to for example a I20 module, it can be configured as a contact sensor
  • ControllableFan: uses output value 0-100 to control a fan speed (on for example a dimmer or a 0-10V output module)
  • MotionSensor: when an input is connected to for example a I20 module, it can be configured as a motion sensor

• movementDuration: in the case of WindowCovering this value indicates how long it takes for the screen to move from the full down position to the full up position (typically longer than the downwards movement). This value is in milliseconds.

Finding the Identifier

The Domintell plugin runs an interface on port 18081 that lets you run the APPINFO command on the master. This is done by pointing your browser to "http://homebridge-ip:18081/appinfo" (the IP address of your homebridge server; not Domintell). The APPINFO itself is sent the console output of HomeBridge and will look like this:

[9/2/2021, 7:20:25 PM] [HomebridgeDomintell] APPINFO message received: 'APPINFO (PROG M 38.4 00/00/00 00h00 Rev=0 CP=UTF8) => domintell config :
BIR  60A2-1GARAGE[Home|Gelijkvloers|Garage]
BIR  60A2-2WASPLAATS[Home|Gelijkvloers|Wasplaats]
BIR  60A2-3KELDER (technische ruimte)[Home|Kelder|technische ruimte]
BIR  60A2-4KELDER (onder keuken)[Home|Kelder|kelder onder keuken]
DAL    89-01KEUKEN Schuifraam 3spots[Home|Gelijkvloers|Keuken][TYPE=LED]
DAL    89-02ZITHOEK Schuifdeur 2spots[Home|Gelijkvloers|Zithoek][TYPE=LED]
DAL    89-03KEUKEN gang 2spots[Home|Gelijkvloers|Keuken][TYPE=LED]

The identifier starts with the interface type (3 characters), and ends right before the name that is defined in the Domintell software. In this case the first identifer from the list would be BIR 60A2-1.

Example config file

{
    "name": "HomebridgeDomintell",
    "platform": "HomebridgeDomintell",
    "ip": "192.168.0.1",
    "port": 17481,
    "username": "",
    "password": "",
    "accessories": [
        {
            "identifier": "DAL    89-01",
            "name": "Living room lights",
            "type": "DimmableLightbulb"
        },
        {
            "identifier": "DAL    89-02",
            "name": "Kitchen Lights",
            "type": "DimmableLightbulb"
        },
        {
            "identifier": "BIR  60A2-2",
            "name": "Toilet Light",
            "type": "Lightbulb"
        },
        {
            "identifier": "PRL   130",
            "name": "Temperature Kitchen",
            "type": "TemperatureSensor"
        },
        {
            "identifier": "DET  1804-1",
            "name": "Garage Motion Detector",
            "type": "MotionSensor"
        },
        {
            "identifier": "I20   23A-2",
            "name": "Garage Side Door",
            "type": "ContactSensor"
        },
        {
            "identifier": "I20   23A-F",
            "name": "Garden Motion Detector",
            "type": "MotionSensor"
        },
        {
            "identifier": "TRV  2535-3",
            "name": "Living room window covering",
            "type": "WindowCovering",
            "movementDuration": 16000
        }
    ]
}