Homebridge Tasmota Control

Homebridge plugin for Tasmota flashed devices.

Package Requirements

| Package | Installation | Role | Required | | --- | --- | --- | --- | | Homebridge | Homebridge Wiki | HomeKit Bridge | Required | | Config UI X | Config UI X Wiki | Homebridge Web User Interface | Recommended | | Tasmota Control | Plug-In Wiki | Homebridge Plug-In | Required |

About The Plugin

• Plugin work with Tasmota v6.0.0 and abowe.

• Support Mitsubishi HVAC:

• Precompiled ESP firmware for MiElHVAC are in firmware folder.

• If You need firmware for specific ESP please go to Firmware for MiElHVAC and meke request.

  • Heater Cooler:
    • Power ON/OFF.
    • Operating mode AUTO/HEAT/COOL.
    • Temperature HEATING/COOLING/AUTO.
    • Fan speed OFF/QUIET/1/2/3/4/AUTO.
    • Swing mode AUTO/SWING.
    • Physical lock controls LOCK/UNLOCK.
    • Temperature display unit °F/°C.
  • Buttons:
    • For direct device control.
      • Power ON/OFF.
      • Operating mode HEAT/DRY/COOL/FAN/AUTO.
      • Fan speed OFF/QUIET/1/2/3/4/AUTO.
      • Vane H LEFT/LEFT MIDDLE/CENTER/RIGHT MIDDLE/RIGHT/SPLIT/SWING.
      • Vane V AUTO/UP/UP MIDDLE/CENTER/DOWN MIDDLE/DOWN/SWING.
      • Air direction INDIRECT/DIRECT/EVEN.
      • Prohibit POWER/MODE/TEMPERATURE/ALL.
      • Physical lock controls LOCK/UNLOCK.
      • Presets SET/UNSET.
  • Sensors:
    • For automation and notifications.
      • State sensors:
        • Power ON/OFF.
        • Operating mode HEAT/DRY/COOL/FAN/AUTO.
        • Fan speed OFF/QUIET/1/2/3/4/AUTO.
        • Vane H AUTO/1/2/3/4/5/SPLIT/SWING.
        • Vane V AUTO/1/2/3/4/5/SWING.
        • Air direction INDIRECT/DIRECT/EVEN.
        • Physical lock controls LOCK/UNLOCK.
        • Presets ACTIV/UNACTIV.
        • Operation stage NORMAL/DEFROST/PREHEAT/STANDBY.
        • Fan stage OFF/QUIET/1/2/3/4/5.
        • Mode stage AUTO OFF/AUTO FAN/AUTO HEAT/AUTO COOL.
        • Remote temperature.
      • Temperature sensors:
        • Room temperature.
        • Outdoor temperature.
  • Functions:
    • Frost protect

• Supported relay devices:

  • Light - Power ON/OFF, Dimmer, Color Temperature, Hue, Saturation
  • Outlet - Power ON/OFF
  • Switch - Power ON/OFF
  • Fan - Fan ON/OFF, Speed, Light ON/OFF

• Supported Sensors:

  • Temperature - Temperature, Dew Point, Reference, Obj, Amb
  • Humidity
  • Carbon Dioxyde
  • Ambient Light
  • Motion
  • Power
  • Energy
  • Current
  • Voltage
  • Power Factor
  • Frequency

Configuration

• Run this plugin as a Child Bridge (Highly Recommended), this prevent crash Homebridge if plugin crashes.
• Install and use Homebridge Config UI X to configure this plugin (Highly Recommended).
• The sample-config.json can be used as an alternative, make a backup copy before making any changes.

| Key | Description | | --- | --- | | name | Here set the accessory Name to be displayed in Homebridge/HomeKit. | | host | Here set the Hsostname or Address IP of the Device.| | auth | If enabled, authorizatins credentials will be used for login. | | user | Here set the authorization Username. | | passwd | Here set the authorization Password. | | disableAccessory | If enabled, the accessory will be disabled. | | miElHvac.heatDryFanMode | Here select the operatiing mode for Heat, only for Mitsubishio AC. | | miElHvac.coolDryFanMode | Here select the operatiing mode for Cool, only for Mitsubishio AC. | | miElHvac.autoDryFanMode | Here select the operatiing mode for Auto, only for Mitsubishio AC. | | miElHvac.temperatureSensor | This enable extra Room temperature sensor to use with automations in HomeKit app. | | miElHvac.temperatureSensorOutdoor | This enable extra Outdoor temperature sensor to use with automations in HomeKit app. | | miElHvac.remoteTemperatureSensor | Object of remote temperature sensor. | | miElHvac.remoteTemperatureSensor.enable | This activate the function. | | miElHvac.remoteTemperatureSensor.path | Here set the path to the temperature sensor, the request need to return value. | | miElHvac.remoteTemperatureSensor.refreshInterval | Here set remote sensor refresh interval. | | miElHvac.remoteTemperatureSensor.auth | If enabled, authorizatins credentials will be used for remote sensor. | | miElHvac.remoteTemperatureSensor.user | Here set the authorization Username. | | miElHvac.remoteTemperatureSensor.passwd | Here set the authorization Password. | | miElHvac.presets | Array of presets sensors. | | miElHvac.presets.name | Here You can schange the Preset Name which is exposed to the Homebridge/HomeKit. | | miElHvac.presets.mode | Here set the operation mode. | | miElHvac.presets.setTemp | Here set the target temperature. | | miElHvac.presets.fanSpeed | Here set the fan speed. | | miElHvac.presets.swingV | Here set the vane vertical direction. | | miElHvac.presets.swingH | Here set the vane horizontal direction. | | miElHvac.presets.displayType | Here select display type in HomeKit, 0 - None/Disabled, 1 - Outlet, 2 - Switch, 3 - Motion Sensor, 4 - Occupancy Sensor, 5 - Contact Sensor. | | miElHvac.buttons | Array of buttons sensors. | | miElHvac.buttons.name | Here set Button Name which You want expose to the Homebridge/HomeKit. | | miElHvac.buttons.mode | Here select button function mode. | | miElHvac.buttons.displayType | Here select display type in HomeKit, 0 - None/Disabled, 1 - Outlet, 2 - Switch, 3 - Motion Sensor. | | miElHvac.buttons.namePrefix | Here enable/disable the accessory name as a prefix for button name. | | miElHvac.sensors | Array of sensors sensors. | | miElHvac.sensors.name | Here set Sensor Name which You want expose to the Homebridge/HomeKit. | | miElHvac.sensors.mode | Here select sensor function mode. | | miElHvac.sensors.displayType | Here select display type in HomeKit, 0 - None/Disabled, 1 - Motion Sensor, 2 - Occupancy Sensor, 3 - Contact Sensor. | | miElHvac.sensors.namePrefix | Here enable/disable the accessory name as a prefix for sensor name. | | miElHvac.frostProtect | Object of frost protect function. | | miElHvac.frostProtect.enable | This activate frost protect function. | | miElHvac.frostProtect.lowTemp | Here set the low temperature at which device start to frost protect. | | miElHvac.frostProtect.highTemp | Here set the high temperature at which device start to frost protect. | | relaysNamePrefix | Here enable/disable the accessory name as a prefix for relays name. | | relaysDisplayType | Here select characteristic display type for relays which are exposed in the HomeKit app. | | lightsNamePrefix | Here enable/disable the accessory name as a prefix for lights name. | | fansNamePrefix | Here enable/disable the accessory name as a prefix for fan name. | | sensorsNamePrefix | Here enable/disable the accessory name as a prefix for sensors name. | | loadNameFromDevice | If enabled, the accessory name will be loaded direct from device. | | refreshInterval | Here set the data refresh time in (sec). | | disableLogDeviceInfo | If enabled, add ability to disable log device info by every connections device to the network. | | disableLogInfo | If enabled, disable log info, all values and state will not be displayed in Homebridge log console. | | disableLogSuccess | If enabled, disable logging device success. | | disableLogWarn | If enabled, disable logging device warnings. | | disableLogError | If enabled, disable logging device error. | | enableDebugMode | If enabled, deep log will be present in homebridge console. |